This blog site contains the result for CCNA2 Version 4.0 Exams. I am posting this for those who are taking the Cisco Course, especially CCNA 2 and for other CCNA i'll be posting the exam result as soon as possible. However, I would like to ask a little favor though. Please, kindly click on all the Google Adsense on the right side.
Thank you and good luck with your test.
Sunday, 17 February 2008
Module 1 Exam
1. If a router cannot find a valid configuration file during the startup sequence, what will occur?
The startup sequence will reset.
* The router will prompt the user for a response to enter setup mode.
The startup sequence will halt until a valid configuration file is acquired.
The router will generate a default configuration file based on the last valid configuration.
The router will monitor local traffic to determine routing protocol configuration requirements.
2. [Picture]
Refer to the exhibit. The network administrator has configured the router with the interface IP addresses shown for the directly connected networks. Pings from the router to hosts on the connected networks or pings between router interfaces are not working. What is the most likely problem?
The destination networks do not exist.
The IP addresses on the router interfaces must be configured as network addresses and not host addresses.
* The interfaces must be enabled with the no shutdown command.
Each interface must be configured with the clock rate command.
3. [Picture]
Refer to the exhibit. What can be concluded from the routing table output in the exhibit? (Choose two.)
This router only has two interfaces.
The router interfaces are not operational yet.
This router is configured to forward packets to remote networks.
* The FastEthernet0/0 and Serial0/0/0 interfaces of this router were configured with an IP address and the no shutdown command.
* An IP packet received by this router with a destination address of 198.18.9.1 will be forwarded out of the Serial0/0/0 interface.
4. [Picture]
Refer to the exhibit. The frame shown in the exhibit was received by the router. The router interfaces are operational. How will the router process this frame? (Choose two.)
The router will change the source and destination IP address in the packet before forwarding the frame.
* The router will change the frame type to one supported by the WAN link before forwarding the frame.
The router will use the destination MAC address to determine which interface to forward the packet.
The router will look up the MAC address of the S0/0/0 interface in the ARP table and add it to the frame before forwarding.
* The frame was received on the Fa0/0 interface of the router and will be switched to the S0/0/0 interface.
The frame was received on the S0/0/0 interface of the router and will be switched to the Fa0/0 interface.
5. Passwords can be used to restrict access to all or parts of the Cisco IOS. Select the modes and interfaces that can be protected with passwords. (Choose three.)
* VTY interface
* console interface
Ethernet interface
secret EXEC mode
* privileged EXEC mode
router configuration mode
6. Which two statements correctly describe the components of a router? (Choose two.)
RAM permanently stores the configuration file used during the boot sequence.
* ROM contains diagnostics executed on hardware modules.
NVRAM stores a backup copy of the IOS used during the boot sequence.
* Flash memory does not lose its contents during a reboot.
ROM contains the most current and most complete version of the IOS.
Flash contains boot system commands to identify the location of the IOS.
7. [Picture]
Refer to the exhibit. After host 2 is connected to the switch on the LAN, host 2 is unable to communicate with host 1. What is the cause of this problem?
The subnet mask of host 2 is incorrect.
* Host 1 and host 2 are on different networks.
The switch needs an IP address that is not configured.
The router LAN interface and host 1 are on different networks.
The IP address of host 1 is on a different network than is the LAN interface of the router.
8. Which are functions of a router? (Choose three.)
* packet switching
extension of network segments
* segmentation of broadcast domains
* selection of best path based on logical addressing
election of best path based on physical addressing
9. [Picture]
Refer to the exhibit. All routers have a route in its routing table to each network that is shown in the exhibit. Default routes have not been issued on these routers. What can be concluded about how packets are forwarded in this network? (Choose two.)
If RouterC receives a packet that is destined for 10.5.1.1, it will be forwarded out interface Fa0/0.
* If RouterA receives a packet that is destined for 192.168.3.146, it will be forwarded out interface S0/0/1.
* If RouterB receives a packet that is destined for 10.5.27.15, it will be forwarded out interface S0/0/1.
If RouterB receives a packet that is destined for 172.20.255.1, it will be forwarded out interface S0/0/0.
If RouterC receives a packet that is destined for 192.16.5.101, it will be forwarded out interface S0/0/1.
10. [Picture]
The serial connection shown in the graphic needs to be configured. Which configuration commands must be made on the Sydney router to establish connectivity with the Melbourne site? (Choose three.)
* Sydney(config-if)# ip address 201.100.53.2 255.255.255.0
* Sydney(config-if)# no shutdown
Sydney(config-if)# ip address 201.100.53.1 255.255.255.224
* Sydney(config-if)# clock rate 56000
Sydney(config-if)# ip host Melbourne 201.100.53.2
11. [Picture]
Refer to the exhibit. What can be concluded from the output of the running-configuration of a router?
The passwords are encrypted.
The current configuration was saved to NVRAM.
The configuration that is shown will be the one used on the next reboot.
* The commands that are displayed determine the current operation of the router.
12. [Picture]
Refer to the exhibit. Host A pings host B. When R4 accepts the ping into the Ethernet interface, what two pieces of header information are included? (Choose two.)
source IP address: 192.168.10.129
source IP address: 192.168.10.129
source IP address: BBBB.3333.5677
destination IP address: 192.168.10.33
* destination IP address: 192.168.10.134
* destination MAC address: 9999.DADC.1234
13. What is the outcome of entering these commands?
R1(config)# line vty 0 4
R1(config-line)# password check123
R1(config-line)# login
ensures that a password is entered before entering user EXEC mode
* sets the password to be used for connecting to this router via Telnet
requires check123 to be entered before the configuration can be saved
creates a local user account for logging in to a router or switch
14. Which of the following is the correct flow of routines for a router startup?
* load bootstrap, load IOS, apply configuration
load bootstrap, apply configuration, load IOS
load IOS, load bootstrap, apply configuration, check hardware
check hardware, apply configuration, load bootstrap, load IOS
15. What three processes does a router execute when it receives a packet from one network that is destined for another network? (Choose three.)
* decapsulates the Layer 3 packet by stripping off the Layer 2 frame header
uses the destination MAC Address in the IP Header to look up the next-hop address in the routing table
leaves the Layer 2 frame header intact when decapsulating the Layer 3 packet
* uses the destination IP Address in the IP header to look up the next-hop address in the routing table
* encapsulates the Layer 3 packet into the new Layer 2 frame and forwards it out the exit interface
encapsulates the Layer 3 packet into a special Layer 1 frame and forwards it to the exit interface
16. The network administrator needs to connect two routers directly via their FastEthernet ports. What cable should the network administrator use?
straight-through
rollover
* cross-over
serial
17. Which two statements describe characteristics of load balancing? (Choose two.)
Load balancing occurs when a router sends the same packet to different destination networks.
Load balancing occurs when a router sends the same packet to different destination networks.
* Load balancing allows a router to forward packets over multiple paths to the same destination network.
* Unequal cost load balancing is supported by EIGRP.
If multiple paths with different metrics to a destinations exist, the router cannot support load balancing.
18. What information about the router and its startup process can be gathered from the output of the show version command? (Choose three.)
* the last restart method
the command buffer contents
the amount of NVRAM and FLASH used
* the configuration register settings
* the location from where the IOS loaded
19. [Picture]
Which interfaces in the exhibit could be used for a leased line WAN connection? (Choose two.)
* 1
2
3
* 4
5
6
20. From what location can a router load the Cisco IOS during the boot process? (Choose two.)
RAM
* TFTP server
NVRAM
setup routine
* Flash memory
terminal
21. A network administrator has just entered new configurations into Router1. Which command should be executed to save configuration changes to NVRAM?
Router1# copy running-config flash
Router1(config)# copy running-config flash
Router1# copy running-config startup-config
* Router1(config)# copy running-config startup-config
Router1# copy startup-config running-config
Router1(config)# copy startup-config running-config
22. What is the default sequence for loading the configuration file?
NVRAM, FLASH, ROM
FLASH, TFTP,CONSOLE
* NVRAM, TFTP, CONSOLE
FLASH, TFTP, ROM
23. What header address information does a router change in the information it receives from an attached Ethernet interface before information is transmitted out another interface?
only the Layer 2 source address
only the Layer 2 destination address
only the Layer 3 source address
only the Layer 3 destination address
* the Layer 2 source and destination address
the Layer 3 source and destination address
The startup sequence will reset.
* The router will prompt the user for a response to enter setup mode.
The startup sequence will halt until a valid configuration file is acquired.
The router will generate a default configuration file based on the last valid configuration.
The router will monitor local traffic to determine routing protocol configuration requirements.
2. [Picture]
Refer to the exhibit. The network administrator has configured the router with the interface IP addresses shown for the directly connected networks. Pings from the router to hosts on the connected networks or pings between router interfaces are not working. What is the most likely problem?
The destination networks do not exist.
The IP addresses on the router interfaces must be configured as network addresses and not host addresses.
* The interfaces must be enabled with the no shutdown command.
Each interface must be configured with the clock rate command.
3. [Picture]
Refer to the exhibit. What can be concluded from the routing table output in the exhibit? (Choose two.)
This router only has two interfaces.
The router interfaces are not operational yet.
This router is configured to forward packets to remote networks.
* The FastEthernet0/0 and Serial0/0/0 interfaces of this router were configured with an IP address and the no shutdown command.
* An IP packet received by this router with a destination address of 198.18.9.1 will be forwarded out of the Serial0/0/0 interface.
4. [Picture]
Refer to the exhibit. The frame shown in the exhibit was received by the router. The router interfaces are operational. How will the router process this frame? (Choose two.)
The router will change the source and destination IP address in the packet before forwarding the frame.
* The router will change the frame type to one supported by the WAN link before forwarding the frame.
The router will use the destination MAC address to determine which interface to forward the packet.
The router will look up the MAC address of the S0/0/0 interface in the ARP table and add it to the frame before forwarding.
* The frame was received on the Fa0/0 interface of the router and will be switched to the S0/0/0 interface.
The frame was received on the S0/0/0 interface of the router and will be switched to the Fa0/0 interface.
5. Passwords can be used to restrict access to all or parts of the Cisco IOS. Select the modes and interfaces that can be protected with passwords. (Choose three.)
* VTY interface
* console interface
Ethernet interface
secret EXEC mode
* privileged EXEC mode
router configuration mode
6. Which two statements correctly describe the components of a router? (Choose two.)
RAM permanently stores the configuration file used during the boot sequence.
* ROM contains diagnostics executed on hardware modules.
NVRAM stores a backup copy of the IOS used during the boot sequence.
* Flash memory does not lose its contents during a reboot.
ROM contains the most current and most complete version of the IOS.
Flash contains boot system commands to identify the location of the IOS.
7. [Picture]
Refer to the exhibit. After host 2 is connected to the switch on the LAN, host 2 is unable to communicate with host 1. What is the cause of this problem?
The subnet mask of host 2 is incorrect.
* Host 1 and host 2 are on different networks.
The switch needs an IP address that is not configured.
The router LAN interface and host 1 are on different networks.
The IP address of host 1 is on a different network than is the LAN interface of the router.
8. Which are functions of a router? (Choose three.)
* packet switching
extension of network segments
* segmentation of broadcast domains
* selection of best path based on logical addressing
election of best path based on physical addressing
9. [Picture]
Refer to the exhibit. All routers have a route in its routing table to each network that is shown in the exhibit. Default routes have not been issued on these routers. What can be concluded about how packets are forwarded in this network? (Choose two.)
If RouterC receives a packet that is destined for 10.5.1.1, it will be forwarded out interface Fa0/0.
* If RouterA receives a packet that is destined for 192.168.3.146, it will be forwarded out interface S0/0/1.
* If RouterB receives a packet that is destined for 10.5.27.15, it will be forwarded out interface S0/0/1.
If RouterB receives a packet that is destined for 172.20.255.1, it will be forwarded out interface S0/0/0.
If RouterC receives a packet that is destined for 192.16.5.101, it will be forwarded out interface S0/0/1.
10. [Picture]
The serial connection shown in the graphic needs to be configured. Which configuration commands must be made on the Sydney router to establish connectivity with the Melbourne site? (Choose three.)
* Sydney(config-if)# ip address 201.100.53.2 255.255.255.0
* Sydney(config-if)# no shutdown
Sydney(config-if)# ip address 201.100.53.1 255.255.255.224
* Sydney(config-if)# clock rate 56000
Sydney(config-if)# ip host Melbourne 201.100.53.2
11. [Picture]
Refer to the exhibit. What can be concluded from the output of the running-configuration of a router?
The passwords are encrypted.
The current configuration was saved to NVRAM.
The configuration that is shown will be the one used on the next reboot.
* The commands that are displayed determine the current operation of the router.
12. [Picture]
Refer to the exhibit. Host A pings host B. When R4 accepts the ping into the Ethernet interface, what two pieces of header information are included? (Choose two.)
source IP address: 192.168.10.129
source IP address: 192.168.10.129
source IP address: BBBB.3333.5677
destination IP address: 192.168.10.33
* destination IP address: 192.168.10.134
* destination MAC address: 9999.DADC.1234
13. What is the outcome of entering these commands?
R1(config)# line vty 0 4
R1(config-line)# password check123
R1(config-line)# login
ensures that a password is entered before entering user EXEC mode
* sets the password to be used for connecting to this router via Telnet
requires check123 to be entered before the configuration can be saved
creates a local user account for logging in to a router or switch
14. Which of the following is the correct flow of routines for a router startup?
* load bootstrap, load IOS, apply configuration
load bootstrap, apply configuration, load IOS
load IOS, load bootstrap, apply configuration, check hardware
check hardware, apply configuration, load bootstrap, load IOS
15. What three processes does a router execute when it receives a packet from one network that is destined for another network? (Choose three.)
* decapsulates the Layer 3 packet by stripping off the Layer 2 frame header
uses the destination MAC Address in the IP Header to look up the next-hop address in the routing table
leaves the Layer 2 frame header intact when decapsulating the Layer 3 packet
* uses the destination IP Address in the IP header to look up the next-hop address in the routing table
* encapsulates the Layer 3 packet into the new Layer 2 frame and forwards it out the exit interface
encapsulates the Layer 3 packet into a special Layer 1 frame and forwards it to the exit interface
16. The network administrator needs to connect two routers directly via their FastEthernet ports. What cable should the network administrator use?
straight-through
rollover
* cross-over
serial
17. Which two statements describe characteristics of load balancing? (Choose two.)
Load balancing occurs when a router sends the same packet to different destination networks.
Load balancing occurs when a router sends the same packet to different destination networks.
* Load balancing allows a router to forward packets over multiple paths to the same destination network.
* Unequal cost load balancing is supported by EIGRP.
If multiple paths with different metrics to a destinations exist, the router cannot support load balancing.
18. What information about the router and its startup process can be gathered from the output of the show version command? (Choose three.)
* the last restart method
the command buffer contents
the amount of NVRAM and FLASH used
* the configuration register settings
* the location from where the IOS loaded
19. [Picture]
Which interfaces in the exhibit could be used for a leased line WAN connection? (Choose two.)
* 1
2
3
* 4
5
6
20. From what location can a router load the Cisco IOS during the boot process? (Choose two.)
RAM
* TFTP server
NVRAM
setup routine
* Flash memory
terminal
21. A network administrator has just entered new configurations into Router1. Which command should be executed to save configuration changes to NVRAM?
Router1# copy running-config flash
Router1(config)# copy running-config flash
Router1# copy running-config startup-config
* Router1(config)# copy running-config startup-config
Router1# copy startup-config running-config
Router1(config)# copy startup-config running-config
22. What is the default sequence for loading the configuration file?
NVRAM, FLASH, ROM
FLASH, TFTP,CONSOLE
* NVRAM, TFTP, CONSOLE
FLASH, TFTP, ROM
23. What header address information does a router change in the information it receives from an attached Ethernet interface before information is transmitted out another interface?
only the Layer 2 source address
only the Layer 2 destination address
only the Layer 3 source address
only the Layer 3 destination address
* the Layer 2 source and destination address
the Layer 3 source and destination address
Module 2 Exam
1. Which of the following are displayed by the Router# show cdp neighbors command? (Choose three.)
* load
platform
* reliability
* holdtime
local interface
2. Why is it advisable to enter a next-hop IP address when creating a static route whose exit interface is an Ethernet network?
* Adding the next-hop address eliminates the need for the router to do any lookups in the routing table before forwarding a packet.
In a multi-access network, the router cannot determine the next-hop MAC address for the Ethernet frame without a next-hop address.
Using a next-hop address in a static route provides a route with a lower metric.
In multi-access networks, using a next-hop address in a static route makes that route a candidate default route.
3. The output of the Router# show interfaces serial 0/1 command displays the following:
* Serial0/1 is up, line protocol is down.
What is the most likely cause for the line protocol being down?
Serial0/1 is shutdown.
There is no cable connecting the routers.
The remote router is using serial 0/0.
No clock rate has been set.
4. A static route that points to the next hop IP will have what administrative distance and metric in the routing table?
administrative distance of 0 and metric of 0
administrative distance of 0 and metric of 1
administrative distance of 1 and metric of 0
administrative distance of 1 and metric of 1
5. Refer to the exhibit. What two commands will change the next-hop address for the 10.0.0.0/8 network from 172.16.40.2 to 192.168.1.2? (Choose two.)
A(config)# no network 10.0.0.0 255.0.0.0 172.16.40.2
* A(config)# no ip address 10.0.0.1 255.0.0.0 172.16.40.2
A(config)# no ip route 10.0.0.0 255.0.0.0 172.16.40.2
* A(config)# ip route 10.0.0.0 255.0.0.0 s0/0/0
A(config)# ip route 10.0.0.0 255.0.0.0 192.168.1.2
6. Refer to the exhibit. A company network engineer is assigned to establish connectivity between the two Ethernet networks so that hosts on the 10.1.1.0/24 subnet can contact hosts on the 10.1.2.0/24 subnet. The engineer has been told to use only static routing for these company routers. Which set of commands will establish connectivity between the two Ethernet networks?
R1(config)# ip route 10.1.2.0 255.255.255.0 192.168.0.1R2(config)# ip route 10.1.1.0 255.255.255.0 192.168.0.2
* R1(config)# ip route 10.1.2.0 255.255.255.0 192.168.0.2R2(config)# ip route 10.1.1.0 255.255.255.0 192.168.0.1
R1(config)# ip route 10.1.1.0 255.255.255.0 192.168.0.2R2(config)# ip route 10.1.2.0 255.255.255.0 192.168.0.1
R1(config)# ip route 10.1.1.0 255.255.255.0 192.168.0.1R2(config)# ip route 10.1.2.0 255.255.255.0 192.168.0.2
R1(config)# ip route 0.0.0.0 0.0.0.0 10.1.2.1R2(config)# ip route 0.0.0.0 0.0.0.0 10.1.1.1
7. Refer to the exhibit. Which static route should be configured on Router1 so that host A will be able to reach host B on the 172.16.0.0 network?
ip route 192.168.0.0 172.16.0.0 255.255.0.0
* ip route 172.16.0.0 255.255.0.0 192.168.0.1
ip route 172.16.0.0 255.255.0.0 S0/0/1
ip route 172.16.0.0 255.255.0.0 S0/0/0
8. What address can be used to summarize networks 172.16.1.0/24, 172.16.2.0/24, 172.16.3.0/24, and 172.16.4.0/24?
172.16.0.0/21
172.16.1.0/22
* 172.16.0.0 255.255.255.248
172.16.0.0 255.255.252.0
9. Refer to the exhibit. What is the significance of the /8 in the route to the 10.0.0.0 network?
It indicates that there are 8 hops between this router and the 10.0.0.0 network.
It represents the time, in milliseconds, it takes for a ping to reply when sent to the 10.0.0.0 network.
* It indicates that there are 8 subnets in the destination network to which the router can forward packets.
It indicates the number of consecutive bits, from the left, in the destination IP address of a packet that must match 10.0.0.0 to use that route.
10. What two devices are responsible for converting the data from the WAN service provider into a form acceptable by the router? (Choose two).
* the serial port of the router
a modem
a switch the ethernet port of the router
a CSU/DSU device
* a DTE device
11. A network administrator enters the following command into Router1: ip route 192.168.0.0 255.255.255.0 S0/1/0. Router1 then receives a packet that is destined for 192.168.0.22/24. After finding the recently configured static route in the routing table, what does Router1 do next to process the packet?
drops the packet because the destination host is not listed in the routing table
* looks up the MAC address of the S0/1/0 interface to determine the destination MAC address of the new frame
performs a recursive lookup for the IP address of the S0/1/0 interface before forwarding the packet
encapsulates the packet into a frame for the WAN link and forwards the packet out the S0/1/0 interface
12. Which piece of information is available from examining the output of the command show ip interface brief?
Interface speed and duplex
Interface MTU
Errors
Interface MAC address
Interface IP address
13. Which of the following is true regarding CDP and the graphic shown?
* CDP running on Router D will gather information about routers A, B, C, and E.
By default, Router A will receive CDP advertisements from routers B and C.
If routers D and E are running different routing protocols, they will not exchange CDP information.
Router E can use CDP to identify the IOS running on Router B.
14. Which two statements describe functions or characteristics of CDP? (Choose two.)
It starts up automatically and allows the device to detect directly connected neighbor devices that use CDP.
* It operates at the network layer and allows two systems to learn about each other.
It creates a topology map of the entire network.
It allows systems to learn about each other even if different network layer protocols are configured.
It forwards advertisements about routes for faster convergence.
15. Hosts on two separate subnets cannot communicate. The network administrator suspects a missing route in one of the routing tables. Which three commands can be used to help troubleshoot Layer 3 connectivity issues? (Choose three.)
ping
* show arp
traceroute
show ip route
* show interface
* show cdp neighbor detail
16. What happens to a static route entry in a routing table when the outgoing interface is not available?
The route is removed from the table.
The router polls neighbors for a replacement route.
* The route remains in the table because it was defined as static.
The router redirects the static route to compensate for the loss of the next hop device.
17. The routers in the diagram use the subnet assignments shown. What is the most efficient route summary that can be configured on Router3 to advertise the internal networks to the cloud?
192.1.1.0/26 and 192.1.1.64/27
192.1.1.128/25
* 192.1.1.0/23 and 192.1.1.64/23
192.1.1.0/24
192.1.1.0/25
192.1.1.0/24 and 192.1.1.64/24
18. Refer to the exhibit. How will packets destined to the 172.16.0.0 network be forwarded?
Router1 will perform recursive lookup and packet will exit S0/0.
Router1 will perform recursive lookup and packet will exit S0/1.
There is no matching interface associated with network 172.16.0.0 so packets will be dropped.
There is no matching interface associated with network 172.16.0.0 so packets will take gateway of last resort and exit out S0/2.
19. A router has one static route to each destination network. Which two scenarios would require an administrator to alter the static routes that are configured on that router? (Choose two.)
The destination network no longer exists.
The destination network is moved to a different interface on the same router.
The path between the source and destination is upgraded with a higher bandwidth link.
A topology change occurs where the existing next-hop address or exit interface is not accessible.
*The remote destination network interface has to be down for 15 minutes of maintenance.
20. Refer to the exhibit. Given the output in the exhibit, how would a clock rate be determined for this link?
The rate would be negotiated by both routers.
A rate would not be selected due to the DCE/DTE connection mismatch.
*The rate configured on the DTE determines the clock rate.
The rate configured on the DCE determines the clock rate.
21. Refer to the exhibit. Which set of commands will configure static routes that will allow the WinterPark and the Altamonte routers to deliver packets from each LAN and direct all other traffic to the Internet?
WinterPark(config)# ip route 0.0.0.0 0.0.0.0 192.168.146.1Altamonte(config)# ip route 10.0.234.0 255.255.255.0 192.168.146.2Altamonte(config)# ip route 0.0.0.0 0.0.0.0 s0/1
* WinterPark(config)# ip route 172.191.67.0 255.255.255.0 192.168.146.1
* WinterPark(config)# ip route 0.0.0.0 0.0.0.0 192.168.146.1Altamonte(config)# ip route 10.0.234.0 255.255.255.0 192.168.146.2
WinterPark(config)# ip route 172.191.67.0 255.255.255.0 192.168.146.1Altamonte(config)# ip route 10.0.234.0 255.255.255.0 192.168.146.2Altamonte(config)# ip route 0.0.0.0 0.0.0.0 s0/0
22. Refer to the exhibit. What two commands are required to provide connectivity between the 192.168.1.0 and 10.0.0.0 networks without requiring recursive lookup? (Choose two.)
A(config)# ip route 10.0.0.0 255.0.0.0 s 0/1/0
* A(config)# ip route 10.0.0.0 255.0.0.0 172.16.40.2
A (config)# ip route 10.0.0.0 255.0.0.0 s 0/0/0
B(config)# ip route 192.168.1.0 255.255.255.0 s 0/0/0
* B (config)# ip route 192.168.1.0 255.255.255.0 172.16.40.1
B(config)# ip route 192.168.1.0 255.255.255.0 s 0/1/0
* load
platform
* reliability
* holdtime
local interface
2. Why is it advisable to enter a next-hop IP address when creating a static route whose exit interface is an Ethernet network?
* Adding the next-hop address eliminates the need for the router to do any lookups in the routing table before forwarding a packet.
In a multi-access network, the router cannot determine the next-hop MAC address for the Ethernet frame without a next-hop address.
Using a next-hop address in a static route provides a route with a lower metric.
In multi-access networks, using a next-hop address in a static route makes that route a candidate default route.
3. The output of the Router# show interfaces serial 0/1 command displays the following:
* Serial0/1 is up, line protocol is down.
What is the most likely cause for the line protocol being down?
Serial0/1 is shutdown.
There is no cable connecting the routers.
The remote router is using serial 0/0.
No clock rate has been set.
4. A static route that points to the next hop IP will have what administrative distance and metric in the routing table?
administrative distance of 0 and metric of 0
administrative distance of 0 and metric of 1
administrative distance of 1 and metric of 0
administrative distance of 1 and metric of 1
5. Refer to the exhibit. What two commands will change the next-hop address for the 10.0.0.0/8 network from 172.16.40.2 to 192.168.1.2? (Choose two.)
A(config)# no network 10.0.0.0 255.0.0.0 172.16.40.2
* A(config)# no ip address 10.0.0.1 255.0.0.0 172.16.40.2
A(config)# no ip route 10.0.0.0 255.0.0.0 172.16.40.2
* A(config)# ip route 10.0.0.0 255.0.0.0 s0/0/0
A(config)# ip route 10.0.0.0 255.0.0.0 192.168.1.2
6. Refer to the exhibit. A company network engineer is assigned to establish connectivity between the two Ethernet networks so that hosts on the 10.1.1.0/24 subnet can contact hosts on the 10.1.2.0/24 subnet. The engineer has been told to use only static routing for these company routers. Which set of commands will establish connectivity between the two Ethernet networks?
R1(config)# ip route 10.1.2.0 255.255.255.0 192.168.0.1R2(config)# ip route 10.1.1.0 255.255.255.0 192.168.0.2
* R1(config)# ip route 10.1.2.0 255.255.255.0 192.168.0.2R2(config)# ip route 10.1.1.0 255.255.255.0 192.168.0.1
R1(config)# ip route 10.1.1.0 255.255.255.0 192.168.0.2R2(config)# ip route 10.1.2.0 255.255.255.0 192.168.0.1
R1(config)# ip route 10.1.1.0 255.255.255.0 192.168.0.1R2(config)# ip route 10.1.2.0 255.255.255.0 192.168.0.2
R1(config)# ip route 0.0.0.0 0.0.0.0 10.1.2.1R2(config)# ip route 0.0.0.0 0.0.0.0 10.1.1.1
7. Refer to the exhibit. Which static route should be configured on Router1 so that host A will be able to reach host B on the 172.16.0.0 network?
ip route 192.168.0.0 172.16.0.0 255.255.0.0
* ip route 172.16.0.0 255.255.0.0 192.168.0.1
ip route 172.16.0.0 255.255.0.0 S0/0/1
ip route 172.16.0.0 255.255.0.0 S0/0/0
8. What address can be used to summarize networks 172.16.1.0/24, 172.16.2.0/24, 172.16.3.0/24, and 172.16.4.0/24?
172.16.0.0/21
172.16.1.0/22
* 172.16.0.0 255.255.255.248
172.16.0.0 255.255.252.0
9. Refer to the exhibit. What is the significance of the /8 in the route to the 10.0.0.0 network?
It indicates that there are 8 hops between this router and the 10.0.0.0 network.
It represents the time, in milliseconds, it takes for a ping to reply when sent to the 10.0.0.0 network.
* It indicates that there are 8 subnets in the destination network to which the router can forward packets.
It indicates the number of consecutive bits, from the left, in the destination IP address of a packet that must match 10.0.0.0 to use that route.
10. What two devices are responsible for converting the data from the WAN service provider into a form acceptable by the router? (Choose two).
* the serial port of the router
a modem
a switch the ethernet port of the router
a CSU/DSU device
* a DTE device
11. A network administrator enters the following command into Router1: ip route 192.168.0.0 255.255.255.0 S0/1/0. Router1 then receives a packet that is destined for 192.168.0.22/24. After finding the recently configured static route in the routing table, what does Router1 do next to process the packet?
drops the packet because the destination host is not listed in the routing table
* looks up the MAC address of the S0/1/0 interface to determine the destination MAC address of the new frame
performs a recursive lookup for the IP address of the S0/1/0 interface before forwarding the packet
encapsulates the packet into a frame for the WAN link and forwards the packet out the S0/1/0 interface
12. Which piece of information is available from examining the output of the command show ip interface brief?
Interface speed and duplex
Interface MTU
Errors
Interface MAC address
Interface IP address
13. Which of the following is true regarding CDP and the graphic shown?
* CDP running on Router D will gather information about routers A, B, C, and E.
By default, Router A will receive CDP advertisements from routers B and C.
If routers D and E are running different routing protocols, they will not exchange CDP information.
Router E can use CDP to identify the IOS running on Router B.
14. Which two statements describe functions or characteristics of CDP? (Choose two.)
It starts up automatically and allows the device to detect directly connected neighbor devices that use CDP.
* It operates at the network layer and allows two systems to learn about each other.
It creates a topology map of the entire network.
It allows systems to learn about each other even if different network layer protocols are configured.
It forwards advertisements about routes for faster convergence.
15. Hosts on two separate subnets cannot communicate. The network administrator suspects a missing route in one of the routing tables. Which three commands can be used to help troubleshoot Layer 3 connectivity issues? (Choose three.)
ping
* show arp
traceroute
show ip route
* show interface
* show cdp neighbor detail
16. What happens to a static route entry in a routing table when the outgoing interface is not available?
The route is removed from the table.
The router polls neighbors for a replacement route.
* The route remains in the table because it was defined as static.
The router redirects the static route to compensate for the loss of the next hop device.
17. The routers in the diagram use the subnet assignments shown. What is the most efficient route summary that can be configured on Router3 to advertise the internal networks to the cloud?
192.1.1.0/26 and 192.1.1.64/27
192.1.1.128/25
* 192.1.1.0/23 and 192.1.1.64/23
192.1.1.0/24
192.1.1.0/25
192.1.1.0/24 and 192.1.1.64/24
18. Refer to the exhibit. How will packets destined to the 172.16.0.0 network be forwarded?
Router1 will perform recursive lookup and packet will exit S0/0.
Router1 will perform recursive lookup and packet will exit S0/1.
There is no matching interface associated with network 172.16.0.0 so packets will be dropped.
There is no matching interface associated with network 172.16.0.0 so packets will take gateway of last resort and exit out S0/2.
19. A router has one static route to each destination network. Which two scenarios would require an administrator to alter the static routes that are configured on that router? (Choose two.)
The destination network no longer exists.
The destination network is moved to a different interface on the same router.
The path between the source and destination is upgraded with a higher bandwidth link.
A topology change occurs where the existing next-hop address or exit interface is not accessible.
*The remote destination network interface has to be down for 15 minutes of maintenance.
20. Refer to the exhibit. Given the output in the exhibit, how would a clock rate be determined for this link?
The rate would be negotiated by both routers.
A rate would not be selected due to the DCE/DTE connection mismatch.
*The rate configured on the DTE determines the clock rate.
The rate configured on the DCE determines the clock rate.
21. Refer to the exhibit. Which set of commands will configure static routes that will allow the WinterPark and the Altamonte routers to deliver packets from each LAN and direct all other traffic to the Internet?
WinterPark(config)# ip route 0.0.0.0 0.0.0.0 192.168.146.1Altamonte(config)# ip route 10.0.234.0 255.255.255.0 192.168.146.2Altamonte(config)# ip route 0.0.0.0 0.0.0.0 s0/1
* WinterPark(config)# ip route 172.191.67.0 255.255.255.0 192.168.146.1
* WinterPark(config)# ip route 0.0.0.0 0.0.0.0 192.168.146.1Altamonte(config)# ip route 10.0.234.0 255.255.255.0 192.168.146.2
WinterPark(config)# ip route 172.191.67.0 255.255.255.0 192.168.146.1Altamonte(config)# ip route 10.0.234.0 255.255.255.0 192.168.146.2Altamonte(config)# ip route 0.0.0.0 0.0.0.0 s0/0
22. Refer to the exhibit. What two commands are required to provide connectivity between the 192.168.1.0 and 10.0.0.0 networks without requiring recursive lookup? (Choose two.)
A(config)# ip route 10.0.0.0 255.0.0.0 s 0/1/0
* A(config)# ip route 10.0.0.0 255.0.0.0 172.16.40.2
A (config)# ip route 10.0.0.0 255.0.0.0 s 0/0/0
B(config)# ip route 192.168.1.0 255.255.255.0 s 0/0/0
* B (config)# ip route 192.168.1.0 255.255.255.0 172.16.40.1
B(config)# ip route 192.168.1.0 255.255.255.0 s 0/1/0
Module 3 Exam
1. Which two statements correctly describe the concepts of administrative distance and metric? (Choose two.)
* Administrative distance refers to the trustworthiness of a particular route.
A router first installs routes with higher administrative distances.
The value of the administrative distance can not be altered by the network
administrator.
* Routes with the smallest metric to a destination indicate the best path.
The metric is always determined based on hop count.
The metric varies depending which Layer 3 protocol is being routed, such as IP or
IPX.
2. [Picture]
Refer to the exhibit. Which statement correctly describes how R1 will determine the best path to R2?
R1 will install a RIP route using network A in its routing table because the
administrative distance of RIP is higher than EIGRP.
R1 will install a RIP route using network A in its routing table because the path
cost from RIP is lower than EIGRP.
* R1 will install an EIGRP route using network B in its routing table because the administrative distance of EIGRP is lower than RIP.
R1 will install an EIGRP route using network B in its routing table because the path cost from EIGRP is lower than RIP.
R1 will install an EIGRP route and a RIP route in its routing table and load
balance between them.
3. Which two statements are true regarding classless routing protocols? (Choose two.)
* sends subnet mask information in routing updates
sends complete routing table update to all neighbors
is supported by RIP version 1
* allows for use of both 192.168.1.0/30 and 192.168.1.16/28 subnets in the same topology
reduces the amount of address space available in an organization
4. Which command would the network administrator issue to determine if load balancing is in effect on a router?
show ip protocols
* show ip route
show ip interface brief
show ip interface
5. Which statement is true regarding routing protocols?
RIP uses hop count and bandwidth as the metric for path selection and sendsupdates periodically.
OSPF is a Cisco proprietary protocol that sends updates triggered by topology changes.
* EIGRP uses DUAL to calculate the shortest path and can be configured to do unequal cost load balancing.
BGP is a path vector interior routing protocol.
6. Which two conditions would create a setting where the use of a distance-vector routing protocol would be efficient? (Choose two.)
the network requires a special hierarchical design
fast convergence of the network is crucial
* the network is using a hub and spoke topology
* the network is using a flat design
there are more than 15 hops between the most distant routers
7. What is the purpose of a routing protocol?
It is used to build and maintain ARP tables.
It provides a method for segmenting and reassembling data packets.
It allows an administrator to devise an addressing scheme for the network.
* It allows a router to share information about known networks with other routers.
It provides a procedure for encoding and decoding data into bits for packet forwarding.
8. Which of the following best describes the operation of distance vector routing protocols?
They use hop count as their only metric.
They only send out updates when a new network is added.
* They send their routing tables to directly connected neighbors.
They flood the entire network with routing updates.
9. Which of the following is associated with link-state routing protocols?
low processor overhead
poison reverse
routing loops
split horizon
* shortest-path first calculations
10. Why is fast convergence desirable in networks that use dynamic routing protocols?
Routers will not allow packets to be forwarded until the network has converged.
Hosts are unable to access their gateway until the network has converged.
* Routers may make incorrect forwarding decisions until the network has converged.
Routers will not allow configuration changes to be made until the network has converged.
11. Which of the following conditions must be met in order for a network to have converged?
The routers in the network are operating with dynamic routing protocols.
The routers in the network are operating with compatible versions of IOS.
The routers in the network are operating with the same routing tables.
* The routers in the network are operating with consistent routing knowledge.
12. Which two statements are true regarding metrics? (Choose two.)
RIP uses bandwidth as a metric.
OSPF uses delay as a metric.
* EIGRP uses bandwidth as a metric.
* OSPF uses cost based on bandwidth as a metric.
RIP uses delay as a metric.
EIGRP uses hop count only as a metric.
13. Which two statements are true regarding the advantages of the use of static routes? (Choose two).
* increased security
reduced effort in configuring routes
* the administrator maintains control over routing
easier to implement in a growing network
reduces the chance of routing errors
increased router resource usage
14. The following line of code is displayed in a routing table:
R 209.165.201.0/24 [120/2] via 192.168.252.2, 00:00:16, S0/0/0
What can be concluded from this output?
A packet destined for host 192.168.252.2 will be forwarded out the interface connected to network 209.165.201.0/24.
* The value, 120, is used to determine the best path when a router has more than one routing protocol configured for the same destination network.
This route was manually configured using the ip route command.
192.168.252.2 is an interface on the router that produced this output.
15. What will be the result of the following commands?
ORL(config)# interface fastethernet 0/0
ORL(config-if)# ip address 172.16.3.1 255.255.255.0
ORL(config-if)# no shutdown
The 172.16.3.0 network will be routed by any dynamic routing protocol automatically.
* A routing table entry is made to the 172.16.3.0 network with a code of “C”.
A static route is required to route traffic to the 172.16.3.0 network.
The commands will be saved to the startup-configuration
16. An engineer creates a static route by entering the Router(config)# ip route 10.0.0.0 255.255.255.0 192.168.1.2 command. What can be concluded about this route?
* The administrative distance of this route is 1.
192.168.1.2 is the address of an interface on this router.
This route will display as a directly connected network in the routing table.
Packets with a destination IP address of 192.168.1.2 will be forwarded to the 10.0.0.0/24 network first.
17. [Picture]
Refer to the exhibit. Router1 and Router2 are running EIGRP. All interfaces are operational and packets can be forwarded between all networks. What information will be found in the routing table for Router1?
Router1 will have 6 directly connected networks.
* The administrative distance of the route to network 172.16.0.0 will be 90.
The metric for routes to 172.16.0.0 will be 1.
The interface that is used to forward packets to 172.16.0.0 will always be the S0/1 interface.
18 The following line of code is present in the routing table:
O 10.16.1.0/27 [110/129] via 192.168.1.5, 00:00:05, Serial0/0/1
What does the number 129 indicate in this output?
* The cost for this link has a value of 129.
The clock rate on this serial interface is set to 129,000.
The next-hop router is 129 hops away from this router.
This route has been updated 129 times in this routing table.
19. A growing medium-sized manufacturing company recently began to have routing instability issues. The company uses static routes and has a mixture of over 30 Cisco and non-Cisco routers. The network administrator has decided to convert the network to dynamic routing. What characteristics of protocols should be considered in this selection process?
Distance vector routing protocols, such as RIP, converge more quickly than do link-state routing protocols.
EIGRP can be used on all of the routers in the company.
* OSPF can be used between the routers.
An exterior routing protocol, such as BGP, is recommended for growing companies.
20. [Picture]
Refer to the exhibit. If RIP is the routing protocol, what is the value of the metric from router A to network 192.168.5.0/24?
* 3
4
56
624
724
21. A router learns two paths with equal metrics to a destination network via the RIP routing protocol. How will the router handle packets to the destination network?
The router will install the first route it learned into the routing table.
* The router will install both routes in the routing table and load balance between the two.
The router will put the first route in the routing table, and denote the second route as a backup route.
The router will pick the path with the higher bandwidth and will place it in the routing table
* Administrative distance refers to the trustworthiness of a particular route.
A router first installs routes with higher administrative distances.
The value of the administrative distance can not be altered by the network
administrator.
* Routes with the smallest metric to a destination indicate the best path.
The metric is always determined based on hop count.
The metric varies depending which Layer 3 protocol is being routed, such as IP or
IPX.
2. [Picture]
Refer to the exhibit. Which statement correctly describes how R1 will determine the best path to R2?
R1 will install a RIP route using network A in its routing table because the
administrative distance of RIP is higher than EIGRP.
R1 will install a RIP route using network A in its routing table because the path
cost from RIP is lower than EIGRP.
* R1 will install an EIGRP route using network B in its routing table because the administrative distance of EIGRP is lower than RIP.
R1 will install an EIGRP route using network B in its routing table because the path cost from EIGRP is lower than RIP.
R1 will install an EIGRP route and a RIP route in its routing table and load
balance between them.
3. Which two statements are true regarding classless routing protocols? (Choose two.)
* sends subnet mask information in routing updates
sends complete routing table update to all neighbors
is supported by RIP version 1
* allows for use of both 192.168.1.0/30 and 192.168.1.16/28 subnets in the same topology
reduces the amount of address space available in an organization
4. Which command would the network administrator issue to determine if load balancing is in effect on a router?
show ip protocols
* show ip route
show ip interface brief
show ip interface
5. Which statement is true regarding routing protocols?
RIP uses hop count and bandwidth as the metric for path selection and sendsupdates periodically.
OSPF is a Cisco proprietary protocol that sends updates triggered by topology changes.
* EIGRP uses DUAL to calculate the shortest path and can be configured to do unequal cost load balancing.
BGP is a path vector interior routing protocol.
6. Which two conditions would create a setting where the use of a distance-vector routing protocol would be efficient? (Choose two.)
the network requires a special hierarchical design
fast convergence of the network is crucial
* the network is using a hub and spoke topology
* the network is using a flat design
there are more than 15 hops between the most distant routers
7. What is the purpose of a routing protocol?
It is used to build and maintain ARP tables.
It provides a method for segmenting and reassembling data packets.
It allows an administrator to devise an addressing scheme for the network.
* It allows a router to share information about known networks with other routers.
It provides a procedure for encoding and decoding data into bits for packet forwarding.
8. Which of the following best describes the operation of distance vector routing protocols?
They use hop count as their only metric.
They only send out updates when a new network is added.
* They send their routing tables to directly connected neighbors.
They flood the entire network with routing updates.
9. Which of the following is associated with link-state routing protocols?
low processor overhead
poison reverse
routing loops
split horizon
* shortest-path first calculations
10. Why is fast convergence desirable in networks that use dynamic routing protocols?
Routers will not allow packets to be forwarded until the network has converged.
Hosts are unable to access their gateway until the network has converged.
* Routers may make incorrect forwarding decisions until the network has converged.
Routers will not allow configuration changes to be made until the network has converged.
11. Which of the following conditions must be met in order for a network to have converged?
The routers in the network are operating with dynamic routing protocols.
The routers in the network are operating with compatible versions of IOS.
The routers in the network are operating with the same routing tables.
* The routers in the network are operating with consistent routing knowledge.
12. Which two statements are true regarding metrics? (Choose two.)
RIP uses bandwidth as a metric.
OSPF uses delay as a metric.
* EIGRP uses bandwidth as a metric.
* OSPF uses cost based on bandwidth as a metric.
RIP uses delay as a metric.
EIGRP uses hop count only as a metric.
13. Which two statements are true regarding the advantages of the use of static routes? (Choose two).
* increased security
reduced effort in configuring routes
* the administrator maintains control over routing
easier to implement in a growing network
reduces the chance of routing errors
increased router resource usage
14. The following line of code is displayed in a routing table:
R 209.165.201.0/24 [120/2] via 192.168.252.2, 00:00:16, S0/0/0
What can be concluded from this output?
A packet destined for host 192.168.252.2 will be forwarded out the interface connected to network 209.165.201.0/24.
* The value, 120, is used to determine the best path when a router has more than one routing protocol configured for the same destination network.
This route was manually configured using the ip route command.
192.168.252.2 is an interface on the router that produced this output.
15. What will be the result of the following commands?
ORL(config)# interface fastethernet 0/0
ORL(config-if)# ip address 172.16.3.1 255.255.255.0
ORL(config-if)# no shutdown
The 172.16.3.0 network will be routed by any dynamic routing protocol automatically.
* A routing table entry is made to the 172.16.3.0 network with a code of “C”.
A static route is required to route traffic to the 172.16.3.0 network.
The commands will be saved to the startup-configuration
16. An engineer creates a static route by entering the Router(config)# ip route 10.0.0.0 255.255.255.0 192.168.1.2 command. What can be concluded about this route?
* The administrative distance of this route is 1.
192.168.1.2 is the address of an interface on this router.
This route will display as a directly connected network in the routing table.
Packets with a destination IP address of 192.168.1.2 will be forwarded to the 10.0.0.0/24 network first.
17. [Picture]
Refer to the exhibit. Router1 and Router2 are running EIGRP. All interfaces are operational and packets can be forwarded between all networks. What information will be found in the routing table for Router1?
Router1 will have 6 directly connected networks.
* The administrative distance of the route to network 172.16.0.0 will be 90.
The metric for routes to 172.16.0.0 will be 1.
The interface that is used to forward packets to 172.16.0.0 will always be the S0/1 interface.
18 The following line of code is present in the routing table:
O 10.16.1.0/27 [110/129] via 192.168.1.5, 00:00:05, Serial0/0/1
What does the number 129 indicate in this output?
* The cost for this link has a value of 129.
The clock rate on this serial interface is set to 129,000.
The next-hop router is 129 hops away from this router.
This route has been updated 129 times in this routing table.
19. A growing medium-sized manufacturing company recently began to have routing instability issues. The company uses static routes and has a mixture of over 30 Cisco and non-Cisco routers. The network administrator has decided to convert the network to dynamic routing. What characteristics of protocols should be considered in this selection process?
Distance vector routing protocols, such as RIP, converge more quickly than do link-state routing protocols.
EIGRP can be used on all of the routers in the company.
* OSPF can be used between the routers.
An exterior routing protocol, such as BGP, is recommended for growing companies.
20. [Picture]
Refer to the exhibit. If RIP is the routing protocol, what is the value of the metric from router A to network 192.168.5.0/24?
* 3
4
56
624
724
21. A router learns two paths with equal metrics to a destination network via the RIP routing protocol. How will the router handle packets to the destination network?
The router will install the first route it learned into the routing table.
* The router will install both routes in the routing table and load balance between the two.
The router will put the first route in the routing table, and denote the second route as a backup route.
The router will pick the path with the higher bandwidth and will place it in the routing table
Module 4 Exam
1. Which event will cause a triggered update?
an update routing timer expires
a corrupt update message is received
* a route is installed in the routing table
the network is converged
2. Three routers running a distance-vector routing protocol lost all power, including the battery backups. When the routers reload, what will happen?
They will share all routes saved in NVRAM prior to the power loss with their directly connected neighbors.
They will multicast hello packets to all other routers in the network to establish neighbor adjacencies.
* They will send updates that include only directly connected routes to their directly connected neighbors.
They will broadcast their full routing table to all routers in the network.
3. What does the RIP holddown timer do?
ensures an invalid route has a metric of 15.
prevents a router from sending any updates after it has introduced a routing loop into the network.
ensures every new route is valid before sending an update.
* instructs routers to ignore updates, for a specified time or event, about possible inaccessible routes.
4. Which two statements are true regarding the function of the RIPv1 routing updates? (Choose two).
updates are broadcast only when there are changes to the topology
* updates are broadcast at regular intervals
broadcast are sent to 0.0.0.0
* broadcasts are sent to 255.255.255.255
updates contain the entire network topology
only changes are included in the updates
5. Which of the following statements are correct about RIP?
uses a broadcast to update all other routers in the network every 60 seconds
uses a multicast address to update other routers every 90 seconds
* will send out an update if there is a failure of a link
updates only contain information about routes that have changed since last update
6. Which two statements describe EIGRP? (Choose two.)
EIGRP can be used with Cisco and non-Cisco routers.
* EIGRP sends triggered updates whenever there is a change in topology that influences the routing information.
EIGRP has an infinite metric of 16.
* EIGRP sends a partial routing table update, which includes just routes that have been changed.
EIGRP broadcasts its updates to all routers in the network.
EIGRP broadcasts its updates to all routers in the network.
7. Which statement is true regarding cisco’s RIP_JITTER variable?
It prevents the synchronization of routing updates by buffering the updates as they leave the router interfaces.
* It prevents the synchronization of routing updates by subtracting a random length of time ranging from 0% to 15% of the specified interval time from the next routing update interval.
It prevents the synchronization of routing updates by causing the router to skip every other scheduled update time.
It prevents the synchronization of routing updates by forcing the router to listen when its time for other updates on the lines before sending its update.
8. What actions will occur after RouterA loses connectivity to network 114.125.16.0? (Choose two.)
* RouterB will include network 123.92.76.0 and 136.125.85.0 in its update to RouterA.
During the next update interval, RouterB will send a RIP update out both ports that includes the inaccessible network.
During the next update interval, RouterC will send an update to RouterB stating that network 114.125.16.0 is accessible in 2 hops.
* Router C will learn of the loss of connectivity to network 114.125.16.0 from RouterB.
RouterB will include network 123.92.76.0 and 136.125.85.0 in its update to RouterC.
9. Which of the following methods does split horizon use to reduce incorrect routing information?
Routing updates are split in half to reduce the update time.
* Information learned from one source is not distributed back to that source.
New route information must be learned from multiple sources to be accepted.
The time between updates is split in half to speed convergence.
New route information is suppressed until the system has converged.
10. [Picture]
The graphic shows a network that is configured to use RIP routing protocol. Router2 detects that the link to Router1 has gone down. It then advertises the network for this link with a hop count metric of 16. Which routing loop prevention mechanism is in effect?
split horizon
error condition
hold-down timer
* route poisoning
count to infinity
11. What is the purpose of the TTL field in the IP header?
used to mark routes as unreachable in updates sent to other routers.
prevents regular update messages from reinstating a route that may have gone bad.
prevents a router from advertising a network through the interface from which the update came.
* limits the time or hops that a packet can traverse through the network before it should be discarded.
defines a maximum metric value for each distance vector routing protocol by setting a maximum hop count.
12. Which of the following can exist in a distance vector network that has not converged? (Choose three.)
* routing loops
* inconsistent traffic forwarding
no traffic forwarding until system converges
* inconsistent routing table entries
routing table updates sent to wrong destinations
13. [Picture]
Refer to the exhibit. The routers in this network are running RIP. Router A has not received an update from Router B in over three minutes. How will Router A respond?
The Holddown timer will wait to remove the route from the table for 60 seconds.
* The Invalid timer will mark the route as unusable if an update has not been received in 180 seconds.
The Update timer will request an update for routes that were learned from Router B.
The Hello timer will expire after 10 seconds and the route will be flushed out of the routing table.
14. A network administrator is evaluating RIP versus EIGRP for a new network. The network will be sensitive to congestion and must respond quickly to topology changes. What are two good reasons to choose EIGRP instead of RIP in this case? (Choose two.)
EIGRP uses periodic updates.
* EIGRP only updates affected neighbors.
EIGRP uses broadcast updates.
* EIGRP updates are partial.
EIGRP uses the efficient Bellman-Ford algorithm.
15. [Picture]
Refer to the exhibit. What path will packets from the 192.168.1.0/24 network travel to reach the 10.0.0.0/8 network if RIP is the active routing protocol?
The path will be router A -> router B -> router C -> router E.
* The path will be router A -> router D -> router E.
Router A will load balance between the router A -> router D -> router E and router A -> router B -> router C -> router E paths.
Packets will alternate paths depending on the order they arrive at router A.
16. Which three routing protocols are distance vector routing protocols? (Choose three).
* RIPv1
* EIGRP
OSPF
IS-IS
* RIPv2
17. What is a routing loop?
a packet bouncing back and forth between two loopback interfaces on a router
a condition where a return path from a destination is different from the outbound path forming a “loop”
* a condition where a packet is constantly transmitted within a series of routers without ever reaching its intended destination
the distribution of routes from one routing protocol into another
18. Which two conditions are most likely to cause a routing loop? (Choose two.)
random jitter
implementation of classful addressing
* inconsistent routing tables
* incorrectly configured static routes
a network converging too quickly
19. What metric does the RIP routing protocol consider to be infinity?
0
15
* 16
224
255
20. What does a router running RIP do first with a new route that is received from an advertisement?
places it immediately in the routing table
* adjusts the metric for the new route to show the added distance for the route
advertises this route out all other interfaces except the one that it came in on
sends a ping packet to verify that the path is a feasible route
21. [Picture]
Refer to the exhibit. If all routers are using RIP, how many rounds of updates will occur before all routers know all networks?
1
2
* 3
4
5
6
an update routing timer expires
a corrupt update message is received
* a route is installed in the routing table
the network is converged
2. Three routers running a distance-vector routing protocol lost all power, including the battery backups. When the routers reload, what will happen?
They will share all routes saved in NVRAM prior to the power loss with their directly connected neighbors.
They will multicast hello packets to all other routers in the network to establish neighbor adjacencies.
* They will send updates that include only directly connected routes to their directly connected neighbors.
They will broadcast their full routing table to all routers in the network.
3. What does the RIP holddown timer do?
ensures an invalid route has a metric of 15.
prevents a router from sending any updates after it has introduced a routing loop into the network.
ensures every new route is valid before sending an update.
* instructs routers to ignore updates, for a specified time or event, about possible inaccessible routes.
4. Which two statements are true regarding the function of the RIPv1 routing updates? (Choose two).
updates are broadcast only when there are changes to the topology
* updates are broadcast at regular intervals
broadcast are sent to 0.0.0.0
* broadcasts are sent to 255.255.255.255
updates contain the entire network topology
only changes are included in the updates
5. Which of the following statements are correct about RIP?
uses a broadcast to update all other routers in the network every 60 seconds
uses a multicast address to update other routers every 90 seconds
* will send out an update if there is a failure of a link
updates only contain information about routes that have changed since last update
6. Which two statements describe EIGRP? (Choose two.)
EIGRP can be used with Cisco and non-Cisco routers.
* EIGRP sends triggered updates whenever there is a change in topology that influences the routing information.
EIGRP has an infinite metric of 16.
* EIGRP sends a partial routing table update, which includes just routes that have been changed.
EIGRP broadcasts its updates to all routers in the network.
EIGRP broadcasts its updates to all routers in the network.
7. Which statement is true regarding cisco’s RIP_JITTER variable?
It prevents the synchronization of routing updates by buffering the updates as they leave the router interfaces.
* It prevents the synchronization of routing updates by subtracting a random length of time ranging from 0% to 15% of the specified interval time from the next routing update interval.
It prevents the synchronization of routing updates by causing the router to skip every other scheduled update time.
It prevents the synchronization of routing updates by forcing the router to listen when its time for other updates on the lines before sending its update.
8. What actions will occur after RouterA loses connectivity to network 114.125.16.0? (Choose two.)
* RouterB will include network 123.92.76.0 and 136.125.85.0 in its update to RouterA.
During the next update interval, RouterB will send a RIP update out both ports that includes the inaccessible network.
During the next update interval, RouterC will send an update to RouterB stating that network 114.125.16.0 is accessible in 2 hops.
* Router C will learn of the loss of connectivity to network 114.125.16.0 from RouterB.
RouterB will include network 123.92.76.0 and 136.125.85.0 in its update to RouterC.
9. Which of the following methods does split horizon use to reduce incorrect routing information?
Routing updates are split in half to reduce the update time.
* Information learned from one source is not distributed back to that source.
New route information must be learned from multiple sources to be accepted.
The time between updates is split in half to speed convergence.
New route information is suppressed until the system has converged.
10. [Picture]
The graphic shows a network that is configured to use RIP routing protocol. Router2 detects that the link to Router1 has gone down. It then advertises the network for this link with a hop count metric of 16. Which routing loop prevention mechanism is in effect?
split horizon
error condition
hold-down timer
* route poisoning
count to infinity
11. What is the purpose of the TTL field in the IP header?
used to mark routes as unreachable in updates sent to other routers.
prevents regular update messages from reinstating a route that may have gone bad.
prevents a router from advertising a network through the interface from which the update came.
* limits the time or hops that a packet can traverse through the network before it should be discarded.
defines a maximum metric value for each distance vector routing protocol by setting a maximum hop count.
12. Which of the following can exist in a distance vector network that has not converged? (Choose three.)
* routing loops
* inconsistent traffic forwarding
no traffic forwarding until system converges
* inconsistent routing table entries
routing table updates sent to wrong destinations
13. [Picture]
Refer to the exhibit. The routers in this network are running RIP. Router A has not received an update from Router B in over three minutes. How will Router A respond?
The Holddown timer will wait to remove the route from the table for 60 seconds.
* The Invalid timer will mark the route as unusable if an update has not been received in 180 seconds.
The Update timer will request an update for routes that were learned from Router B.
The Hello timer will expire after 10 seconds and the route will be flushed out of the routing table.
14. A network administrator is evaluating RIP versus EIGRP for a new network. The network will be sensitive to congestion and must respond quickly to topology changes. What are two good reasons to choose EIGRP instead of RIP in this case? (Choose two.)
EIGRP uses periodic updates.
* EIGRP only updates affected neighbors.
EIGRP uses broadcast updates.
* EIGRP updates are partial.
EIGRP uses the efficient Bellman-Ford algorithm.
15. [Picture]
Refer to the exhibit. What path will packets from the 192.168.1.0/24 network travel to reach the 10.0.0.0/8 network if RIP is the active routing protocol?
The path will be router A -> router B -> router C -> router E.
* The path will be router A -> router D -> router E.
Router A will load balance between the router A -> router D -> router E and router A -> router B -> router C -> router E paths.
Packets will alternate paths depending on the order they arrive at router A.
16. Which three routing protocols are distance vector routing protocols? (Choose three).
* RIPv1
* EIGRP
OSPF
IS-IS
* RIPv2
17. What is a routing loop?
a packet bouncing back and forth between two loopback interfaces on a router
a condition where a return path from a destination is different from the outbound path forming a “loop”
* a condition where a packet is constantly transmitted within a series of routers without ever reaching its intended destination
the distribution of routes from one routing protocol into another
18. Which two conditions are most likely to cause a routing loop? (Choose two.)
random jitter
implementation of classful addressing
* inconsistent routing tables
* incorrectly configured static routes
a network converging too quickly
19. What metric does the RIP routing protocol consider to be infinity?
0
15
* 16
224
255
20. What does a router running RIP do first with a new route that is received from an advertisement?
places it immediately in the routing table
* adjusts the metric for the new route to show the added distance for the route
advertises this route out all other interfaces except the one that it came in on
sends a ping packet to verify that the path is a feasible route
21. [Picture]
Refer to the exhibit. If all routers are using RIP, how many rounds of updates will occur before all routers know all networks?
1
2
* 3
4
5
6
Module 5 Exam
1. [Picture]
Refer to the exhibit. The network that is shown is running RIPv1. The 192.168.10.0/24 network was recently added and will only contain end users. What command or set of commands should be entered on Router1 to prevent RIPv1 updates from being sent to the end user devices on the new network while still allowing this new network to be advertised to other routers?
Router1(config-router)# no router rip
Router1(config-router)# network 192.168.10.0
Router1(config-router)# no network 192.168.10.0
* Router1(config-router)# passive-interface fastethernet 0/0
Router1(config-router)# passive-interface serial 0/0/0
2. The following line was displayed in the output of the show ip route command.
R 192.168.3.0/24 [120/3] via 192.168.2.2, 00:00:30, Serial0/0
What is the value of the routing metric?
* 3
12
20
30
120
3. Which of the following is considered a limitation of RIP v1?
* RIP v1 does not send subnet mask information in its updates.
RIP v1 is not widely supported by networking hardware vendors.
RIP v1 consumes excessive bandwidth by multicasting routing updates using a Class D address.
RIP v1 requires enhanced router processors and extra RAM to function effectively.
RIP v1 does not support load balancing across equal-cost paths.
RIP v1 authentication is complicated and time-consuming to configure.
4. [Picture]
Refer to the exhibit. The Ethernet interface on Router2 goes down and the administrator notices that the route is still in the Router1 routing table. How much longer will Router1 keep the down network in its routing table before marking it as possibly down?
30 seconds
90 seconds
* 155 seconds
180 seconds
255 seconds
5. [Picture]
Refer to the exhibit. Router1 is running RIPv1. What command was entered into Router1 to configure the gateway of last resort?
no auto-summary
ip default-network 0.0.0.0
ip default-gateway 0.0.0.0
* ip route 0.0.0.0 0.0.0.0 S0/0/1
6. What are three characteristics of the RIPv1 routing protocol? (Choose three.)
supports the use of VLSM
* uses hop count as a metric
* considers a metric of 16 as infinity
has an administrative distance of 110 by default
includes the destination IP address and subnet mask in routing updates
calculates metrics using the Bellman Ford algorithm
7. [Picture]
Which of the following would be the correct command sequence to enable RIP on Router B for all connected networks?
RouterB# router rip
RouterB(router)# network 210.36.7.0
RouterB(router)# network 220.17.29.0
RouterB(router)# network 211.168.74.0
RouterB(config)# router rip
RouterB(config-router)# network 198.16.4.0
RouterB(config-router)# network 211.168.74.0
RouterB(config-router)# network 199.84.32.0
RouterB(config)# configure router rip
RouterB(config-router)# network 210.36.7.0
RouterB(config-router)# network 199.84.32.0
RouterB(config-router)# network 211.168.74.0
RouterB(config)# router rip
RouterB(config-router)# network 198.16.4.0
RouterB(config-router)# network 210.36.7.0
RouterB(config-router)# network 211.168.74.0
* RouterB(config)# router rip
RouterB(config-router)# network 198.16.4.0
RouterB(config-router)# network 210.36.7.0
RouterB(config-router)# network 220.17.29.0
8. What is the default update period in seconds for the RIP routing protocol?
10
12
15
20
* 30
60
9. [Picture]
Refer to the exhibit. What can be concluded from the routing table output of router B?
A static default route has been configured on B.
* The default-information originate command has been entered on A.
All traffic that is destined for 192.168.1.1 will be sent to address 0.0.0.0.
Hosts on the 10.16.1.0/27 network have 192.168.1.1 configured as the default gateway address.
10. [Picture]
Refer to the exhibit. A network consists of multiple routers. What can be verified when the show ip protocols command is issued on one of the routers in the network?
whether all routes in the network have been properly added to the routing table
* routing protocol configuration in use for IP on this router
operational status of routing protocols in use on all routers in the network
routing metric of each network that is listed in the routing table
11. [Picture]
Refer to the exhibit. All routers are configured with valid interface addresses in the indicated networks and are running RIPv1. The network is converged. Which routes are present in the routing tables?
All routers have all routes in their routing table.
All routers have all /30 routes, but do not have /24 routes in their routing table.
* All routers have all /30 routes. Routers A and E also have some of the /24 routes in their routing table.
All routers have all /30 routes. Routers B and D also have some of the /24 routes in their routing table.
Routers A and E have all routes. Routers B and D have only /30 routes in their routing table.
Routers A and E have only /24 routes. Routers B and D have only /30 routes in their routing table.
12. Which two statements are true regarding the characteristics of RIPv1? (Choose two).
* It is a distance vector routing protocol.
It advertises the address and subnet mask for routes in routing updates.
The data portion of a RIP message is encapsulated into a TCP segment.
* The data portion of a RIP message is encapsulated into a UDP segment.
It broadcasts updates every 15 seconds.
It allows a maximum of 15 routers in the routing domain.
13. Which command or set of commands will stop the RIP routing process?
RouterB(config)# router rip
RouterB(config-router)# shutdown
RouterB(config)# router rip
RouterB(config-router)# network no 192.168.2.0
* RouterB(config)# no router rip
* RouterB(config)# router no rip
14. [Picture]
Refer to the exhibit. All routers in the exhibit are running RIP v1. The network administrator issues the show ip route command on router A. What routes would appear in the routing table output if the network is converged? (Choose two).
* R 192.168.2.0/24 [120/1]
C 192.168.2.0/24 [120/1]
R 10.10.3.0/24 [120/0]
C 10.10.3.0/24 [120/1]
* R 10.10.1.0/24 [120/2]
R 10.10.1.0/24 [120/3]
15. Which command will display RIP activity as it occurs on a router?
* debug ip rip
show ip route
show ip interface
show ip protocols
debug ip rip config
show ip rip database
16. [Picture]
Refer to the output from the show ip route command. What can be concluded from the output of this router command?
A preferred route to the destination has not been set.
* There are two equal cost paths to network 1.0.0.0.
Both interfaces are being used equally to route traffic.
A variance must be set to load-balance across multiple paths.
17. [Picture]
Refer to the exhibit. Router1 and Router2 are running the RIPv1 protocol. The network administrator configures the command network 10.1.0.0 on Router1. What network will Router1 advertise to Router2?
10.1.0.0/16
10.1.0.0/8
10.0.0.0/16
* 10.0.0.0/8
18. [Picture]
Refer to the exhibit. Pings between the serial interfaces of the routers are successful. Hosts on each LAN can ping the Fa0/0 interface of the router to which they are directly connected through the switch. However, pings between hosts on the 10.1.1.0/24 and 10.1.2.0/24 networks are unsuccessful. What is a likely cause of this problem?
The Fa0/0 interface on R1 is configured as a passive interface.
The Fa0/0 interfaces on each router is shutdown.
* RIP is configured incorrectly on R1.
Automatic summarization is preventing the routing updates from being forwarded.
The network has not converged and R2 must wait 12 more seconds before receiving a full routing table update from R1.
19. What will happen if an interface IP address is entered for the address portion of the network command in a RIPv1 configuration instead of a network address?
The router will reject the command.
A route to the host address will be added to outgoing RIP updates.
A route to the host address will be added to the routing table.
* All interfaces in the same classful network as the configured address will be included in the RIPv1 routing process.
20. [Picture]
Refer to the exhibit. All routers that are shown are running the RIP routing protocol. All unknown IP traffic must be forwarded to the ISP. What router or set of routers are recommended to have both a default route and the default-information originate command issued to implement this forwarding policy?
only Router1
* only the gateway router
all routers in the network
only the routers with LANs needing Internet access
Refer to the exhibit. The network that is shown is running RIPv1. The 192.168.10.0/24 network was recently added and will only contain end users. What command or set of commands should be entered on Router1 to prevent RIPv1 updates from being sent to the end user devices on the new network while still allowing this new network to be advertised to other routers?
Router1(config-router)# no router rip
Router1(config-router)# network 192.168.10.0
Router1(config-router)# no network 192.168.10.0
* Router1(config-router)# passive-interface fastethernet 0/0
Router1(config-router)# passive-interface serial 0/0/0
2. The following line was displayed in the output of the show ip route command.
R 192.168.3.0/24 [120/3] via 192.168.2.2, 00:00:30, Serial0/0
What is the value of the routing metric?
* 3
12
20
30
120
3. Which of the following is considered a limitation of RIP v1?
* RIP v1 does not send subnet mask information in its updates.
RIP v1 is not widely supported by networking hardware vendors.
RIP v1 consumes excessive bandwidth by multicasting routing updates using a Class D address.
RIP v1 requires enhanced router processors and extra RAM to function effectively.
RIP v1 does not support load balancing across equal-cost paths.
RIP v1 authentication is complicated and time-consuming to configure.
4. [Picture]
Refer to the exhibit. The Ethernet interface on Router2 goes down and the administrator notices that the route is still in the Router1 routing table. How much longer will Router1 keep the down network in its routing table before marking it as possibly down?
30 seconds
90 seconds
* 155 seconds
180 seconds
255 seconds
5. [Picture]
Refer to the exhibit. Router1 is running RIPv1. What command was entered into Router1 to configure the gateway of last resort?
no auto-summary
ip default-network 0.0.0.0
ip default-gateway 0.0.0.0
* ip route 0.0.0.0 0.0.0.0 S0/0/1
6. What are three characteristics of the RIPv1 routing protocol? (Choose three.)
supports the use of VLSM
* uses hop count as a metric
* considers a metric of 16 as infinity
has an administrative distance of 110 by default
includes the destination IP address and subnet mask in routing updates
calculates metrics using the Bellman Ford algorithm
7. [Picture]
Which of the following would be the correct command sequence to enable RIP on Router B for all connected networks?
RouterB# router rip
RouterB(router)# network 210.36.7.0
RouterB(router)# network 220.17.29.0
RouterB(router)# network 211.168.74.0
RouterB(config)# router rip
RouterB(config-router)# network 198.16.4.0
RouterB(config-router)# network 211.168.74.0
RouterB(config-router)# network 199.84.32.0
RouterB(config)# configure router rip
RouterB(config-router)# network 210.36.7.0
RouterB(config-router)# network 199.84.32.0
RouterB(config-router)# network 211.168.74.0
RouterB(config)# router rip
RouterB(config-router)# network 198.16.4.0
RouterB(config-router)# network 210.36.7.0
RouterB(config-router)# network 211.168.74.0
* RouterB(config)# router rip
RouterB(config-router)# network 198.16.4.0
RouterB(config-router)# network 210.36.7.0
RouterB(config-router)# network 220.17.29.0
8. What is the default update period in seconds for the RIP routing protocol?
10
12
15
20
* 30
60
9. [Picture]
Refer to the exhibit. What can be concluded from the routing table output of router B?
A static default route has been configured on B.
* The default-information originate command has been entered on A.
All traffic that is destined for 192.168.1.1 will be sent to address 0.0.0.0.
Hosts on the 10.16.1.0/27 network have 192.168.1.1 configured as the default gateway address.
10. [Picture]
Refer to the exhibit. A network consists of multiple routers. What can be verified when the show ip protocols command is issued on one of the routers in the network?
whether all routes in the network have been properly added to the routing table
* routing protocol configuration in use for IP on this router
operational status of routing protocols in use on all routers in the network
routing metric of each network that is listed in the routing table
11. [Picture]
Refer to the exhibit. All routers are configured with valid interface addresses in the indicated networks and are running RIPv1. The network is converged. Which routes are present in the routing tables?
All routers have all routes in their routing table.
All routers have all /30 routes, but do not have /24 routes in their routing table.
* All routers have all /30 routes. Routers A and E also have some of the /24 routes in their routing table.
All routers have all /30 routes. Routers B and D also have some of the /24 routes in their routing table.
Routers A and E have all routes. Routers B and D have only /30 routes in their routing table.
Routers A and E have only /24 routes. Routers B and D have only /30 routes in their routing table.
12. Which two statements are true regarding the characteristics of RIPv1? (Choose two).
* It is a distance vector routing protocol.
It advertises the address and subnet mask for routes in routing updates.
The data portion of a RIP message is encapsulated into a TCP segment.
* The data portion of a RIP message is encapsulated into a UDP segment.
It broadcasts updates every 15 seconds.
It allows a maximum of 15 routers in the routing domain.
13. Which command or set of commands will stop the RIP routing process?
RouterB(config)# router rip
RouterB(config-router)# shutdown
RouterB(config)# router rip
RouterB(config-router)# network no 192.168.2.0
* RouterB(config)# no router rip
* RouterB(config)# router no rip
14. [Picture]
Refer to the exhibit. All routers in the exhibit are running RIP v1. The network administrator issues the show ip route command on router A. What routes would appear in the routing table output if the network is converged? (Choose two).
* R 192.168.2.0/24 [120/1]
C 192.168.2.0/24 [120/1]
R 10.10.3.0/24 [120/0]
C 10.10.3.0/24 [120/1]
* R 10.10.1.0/24 [120/2]
R 10.10.1.0/24 [120/3]
15. Which command will display RIP activity as it occurs on a router?
* debug ip rip
show ip route
show ip interface
show ip protocols
debug ip rip config
show ip rip database
16. [Picture]
Refer to the output from the show ip route command. What can be concluded from the output of this router command?
A preferred route to the destination has not been set.
* There are two equal cost paths to network 1.0.0.0.
Both interfaces are being used equally to route traffic.
A variance must be set to load-balance across multiple paths.
17. [Picture]
Refer to the exhibit. Router1 and Router2 are running the RIPv1 protocol. The network administrator configures the command network 10.1.0.0 on Router1. What network will Router1 advertise to Router2?
10.1.0.0/16
10.1.0.0/8
10.0.0.0/16
* 10.0.0.0/8
18. [Picture]
Refer to the exhibit. Pings between the serial interfaces of the routers are successful. Hosts on each LAN can ping the Fa0/0 interface of the router to which they are directly connected through the switch. However, pings between hosts on the 10.1.1.0/24 and 10.1.2.0/24 networks are unsuccessful. What is a likely cause of this problem?
The Fa0/0 interface on R1 is configured as a passive interface.
The Fa0/0 interfaces on each router is shutdown.
* RIP is configured incorrectly on R1.
Automatic summarization is preventing the routing updates from being forwarded.
The network has not converged and R2 must wait 12 more seconds before receiving a full routing table update from R1.
19. What will happen if an interface IP address is entered for the address portion of the network command in a RIPv1 configuration instead of a network address?
The router will reject the command.
A route to the host address will be added to outgoing RIP updates.
A route to the host address will be added to the routing table.
* All interfaces in the same classful network as the configured address will be included in the RIPv1 routing process.
20. [Picture]
Refer to the exhibit. All routers that are shown are running the RIP routing protocol. All unknown IP traffic must be forwarded to the ISP. What router or set of routers are recommended to have both a default route and the default-information originate command issued to implement this forwarding policy?
only Router1
* only the gateway router
all routers in the network
only the routers with LANs needing Internet access
Module 6 Exam
1. [Picture]
What two advantages does CIDR provide to a network? (Choose two.)
* reduced routing table size
dynamic address assignment
automatic route redistribution
* reduced routing update traffic
utomatic summarization at classful boundaries
2. [Picture]
Refer to the exhibit. The network administrator wants to create a subnet for the point-to-point connection between the two routers. Which subnetwork mask would provide enough addresses for the point-to-point link with the least number of wasted addresses?
255.255.255.192
255.255.255.224
255.255.255.240
255.255.255.248
* 255.255.255.252
3. [Picture]
Refer to the exhibit. A network engineer is summarizing the two groups of routes on router R1 shown in the exhibit. Which summarization will work for all the subnets?
192.168.0.0/23
192.168.0.0/22
* 192.168.0.0/21
192.168.0.0/20
4. Which of the following are contained in the routing updates of classless routing protocols? (Choose two.)
* 32-bit address
next hop router interface
* subnet mask
unicast host address
Layer 2 address
5. Which of the following problems does VLSM help to alleviate?
* the shortage of IP addresses
the difficulty of assigning static IP addresses to hosts in large enterprises
the complexity of implementing advanced routing protocols such as OSPF and EIGRP
the shortage of network administrators qualified in the use of RIP v1 and IGRP
6. What does VLSM allow a network administrator to do?
utilize one subnet mask throughout an autonomous system
* utilize multiple subnet masks in the same IP address space
utilize IGRP as the routing protocol in an entire autonomous system
utilize multiple routing protocols within an autonomous system
7. [Picture]
Refer to the exhibit. What subnet mask will be applied if Router A sends a RIPv1 update for the network 172.16.1.0 to Router B?
none
8
16
* 24
8. [Picture]
Refer to the exhibit. The network administrator wants to minimize the number of entries in Router1’s routing table. What should the administrator implement on the network?
VLSM
* CIDR
private IP addresses
classful routing
9. A router has a summary route to network 192.168.32.0/20 installed in its routing table. What range of networks are summarized by this route?
192.168.0.0 – 192.168.32.0/24
192.168.0.0 – 192.168.47.0/24
* 192.168.32.0 – 192.168.47.0/24
192.168.32.0 – 192.168.48.0/24
192.168.32.0 – 192.168.63.0/24
10. A network administrator is tasked with dividing up a class C network among the QA, Sales, and Administration departments. The QA department is made up of 10 people, the Sales is made up of 28 people, and the Administration has 6. Which two subnets masks adequately address the QA and Sales departments? (Choose two.)
255.255.255.252 for QA
* 255.255.255.224 for Sales
* 255.255.255.240 for QA
255.255.255.248 for QA
255.255.255.0 for Sales
11. [Picture]
In the network shown in the graphic, three bits were borrowed from the host portion of a Class C address. How many valid host addresses will be unused on the three point-to-point links combined if VLSM is not used?
3
4
12
36
* 84
180
12. A Class C address has been assigned for use in the network shown in the graphic. Using VLSM, which bit mask should be used to provide for the number of host addresses required on Router A, while wasting the fewest addresses?
/31
/30
/29
/28
* /27
/26
13. [Picture]
An additional subnet is required for a new Ethernet link between Router1 and Router2 as shown in the diagram. Which of the following subnet addresses can be configured in this network to provide a maximum of 14 useable addresses for this link while wasting the fewest addresses?
192.1.1.16/26
192.1.1.96/28
192.1.1.160/28
192.1.1.196/27
* 192.1.1.224/28
192.1.1.240/28
14. Which three interior routing protocols support VLSM? (Choose three.)
* OSPF
RIP v1
* RIP v2
* EIGRP
BGP
STP
15. [Picture]
Refer to the exhibit. The number of required host addresses for each subnet in a network is listed in the exhibit. This number includes the host address requirements for all router ports and hosts on that subnet. After all device and router port address assignments are determined, what will be the total number of unused host addresses available?
6
14
* 29
34
40
62
16. [Picture]
Refer to the exhibit. In the network that is shown, the router interfaces are assigned the first address in each subnet. Which IP address would be usable for a host on one of the LANs in this network?
192.168.1.5/30
192.168.2.17/28
192.168.2.63/27
* 192.168.2.130/25
17. [Picture]
Refer to the exhibit. Which address is a broadcast address for one of the subnets that are shown in the exhibit?
192.168.4.3/29
* 192.168.4.15/29
192.168.4.65/26
192.168.4.255/24
18. [Picture]
Refer to the exhibit. A network administrator needs to create two subnetworks from 10.0.0.0/8 for a router running RIPv2. The Admin subnet requires 120 hosts and the Sales subnet requires 58 hosts. The network administrator assigned 10.0.1.128/25 to the Admin subnet. The Sales subnet is given 10.0.1.192/26. What will be the result of this addressing scheme?
Because RIPv2 does not support VLSM, the subnet masks will not be allowed.
The subnets will not have enough host addresses for the given network requirements.
* The subnets overlap and will be rejected by the router.
The router will support the addressing scheme.
19. [Picture]
Refer to the exhibit. A network technician enters the static route in R1 needed to reach network 10.1.1.0/24. A ping from the S0/0/0 interface on R1 to host B fails. The technician begins testing the network and has the following results:
1. pings from R1 to the S0/0/0 interface on R2….successful
2. pings from R1 to the Fa0/0 interface on R2….successful
3. pings from host B to hosts on the 10.1.1.0/24 network….successful
4. pings from host B to the Fa0/0 interface on R2….successful
5. pings from R2 to host B….successful.
What is the likely cause of the failure of the ping from R1 to host B?
* The default gateway on host B is not correctly set.
There are no routes back to networks connected to R1 from R2.
There is a Layer 2 problem between R2 and host B.
Host B has a defective Ethernet card.
20. What is a supernet?
the network for a default route
* a summarization of classful addresses
a network that contains both private and public addresses
a set of discontiguous networks that are controlled by an ISP
What two advantages does CIDR provide to a network? (Choose two.)
* reduced routing table size
dynamic address assignment
automatic route redistribution
* reduced routing update traffic
utomatic summarization at classful boundaries
2. [Picture]
Refer to the exhibit. The network administrator wants to create a subnet for the point-to-point connection between the two routers. Which subnetwork mask would provide enough addresses for the point-to-point link with the least number of wasted addresses?
255.255.255.192
255.255.255.224
255.255.255.240
255.255.255.248
* 255.255.255.252
3. [Picture]
Refer to the exhibit. A network engineer is summarizing the two groups of routes on router R1 shown in the exhibit. Which summarization will work for all the subnets?
192.168.0.0/23
192.168.0.0/22
* 192.168.0.0/21
192.168.0.0/20
4. Which of the following are contained in the routing updates of classless routing protocols? (Choose two.)
* 32-bit address
next hop router interface
* subnet mask
unicast host address
Layer 2 address
5. Which of the following problems does VLSM help to alleviate?
* the shortage of IP addresses
the difficulty of assigning static IP addresses to hosts in large enterprises
the complexity of implementing advanced routing protocols such as OSPF and EIGRP
the shortage of network administrators qualified in the use of RIP v1 and IGRP
6. What does VLSM allow a network administrator to do?
utilize one subnet mask throughout an autonomous system
* utilize multiple subnet masks in the same IP address space
utilize IGRP as the routing protocol in an entire autonomous system
utilize multiple routing protocols within an autonomous system
7. [Picture]
Refer to the exhibit. What subnet mask will be applied if Router A sends a RIPv1 update for the network 172.16.1.0 to Router B?
none
8
16
* 24
8. [Picture]
Refer to the exhibit. The network administrator wants to minimize the number of entries in Router1’s routing table. What should the administrator implement on the network?
VLSM
* CIDR
private IP addresses
classful routing
9. A router has a summary route to network 192.168.32.0/20 installed in its routing table. What range of networks are summarized by this route?
192.168.0.0 – 192.168.32.0/24
192.168.0.0 – 192.168.47.0/24
* 192.168.32.0 – 192.168.47.0/24
192.168.32.0 – 192.168.48.0/24
192.168.32.0 – 192.168.63.0/24
10. A network administrator is tasked with dividing up a class C network among the QA, Sales, and Administration departments. The QA department is made up of 10 people, the Sales is made up of 28 people, and the Administration has 6. Which two subnets masks adequately address the QA and Sales departments? (Choose two.)
255.255.255.252 for QA
* 255.255.255.224 for Sales
* 255.255.255.240 for QA
255.255.255.248 for QA
255.255.255.0 for Sales
11. [Picture]
In the network shown in the graphic, three bits were borrowed from the host portion of a Class C address. How many valid host addresses will be unused on the three point-to-point links combined if VLSM is not used?
3
4
12
36
* 84
180
12. A Class C address has been assigned for use in the network shown in the graphic. Using VLSM, which bit mask should be used to provide for the number of host addresses required on Router A, while wasting the fewest addresses?
/31
/30
/29
/28
* /27
/26
13. [Picture]
An additional subnet is required for a new Ethernet link between Router1 and Router2 as shown in the diagram. Which of the following subnet addresses can be configured in this network to provide a maximum of 14 useable addresses for this link while wasting the fewest addresses?
192.1.1.16/26
192.1.1.96/28
192.1.1.160/28
192.1.1.196/27
* 192.1.1.224/28
192.1.1.240/28
14. Which three interior routing protocols support VLSM? (Choose three.)
* OSPF
RIP v1
* RIP v2
* EIGRP
BGP
STP
15. [Picture]
Refer to the exhibit. The number of required host addresses for each subnet in a network is listed in the exhibit. This number includes the host address requirements for all router ports and hosts on that subnet. After all device and router port address assignments are determined, what will be the total number of unused host addresses available?
6
14
* 29
34
40
62
16. [Picture]
Refer to the exhibit. In the network that is shown, the router interfaces are assigned the first address in each subnet. Which IP address would be usable for a host on one of the LANs in this network?
192.168.1.5/30
192.168.2.17/28
192.168.2.63/27
* 192.168.2.130/25
17. [Picture]
Refer to the exhibit. Which address is a broadcast address for one of the subnets that are shown in the exhibit?
192.168.4.3/29
* 192.168.4.15/29
192.168.4.65/26
192.168.4.255/24
18. [Picture]
Refer to the exhibit. A network administrator needs to create two subnetworks from 10.0.0.0/8 for a router running RIPv2. The Admin subnet requires 120 hosts and the Sales subnet requires 58 hosts. The network administrator assigned 10.0.1.128/25 to the Admin subnet. The Sales subnet is given 10.0.1.192/26. What will be the result of this addressing scheme?
Because RIPv2 does not support VLSM, the subnet masks will not be allowed.
The subnets will not have enough host addresses for the given network requirements.
* The subnets overlap and will be rejected by the router.
The router will support the addressing scheme.
19. [Picture]
Refer to the exhibit. A network technician enters the static route in R1 needed to reach network 10.1.1.0/24. A ping from the S0/0/0 interface on R1 to host B fails. The technician begins testing the network and has the following results:
1. pings from R1 to the S0/0/0 interface on R2….successful
2. pings from R1 to the Fa0/0 interface on R2….successful
3. pings from host B to hosts on the 10.1.1.0/24 network….successful
4. pings from host B to the Fa0/0 interface on R2….successful
5. pings from R2 to host B….successful.
What is the likely cause of the failure of the ping from R1 to host B?
* The default gateway on host B is not correctly set.
There are no routes back to networks connected to R1 from R2.
There is a Layer 2 problem between R2 and host B.
Host B has a defective Ethernet card.
20. What is a supernet?
the network for a default route
* a summarization of classful addresses
a network that contains both private and public addresses
a set of discontiguous networks that are controlled by an ISP
Subscribe to:
Posts (Atom)
